| Poster |
Message |
 stang67
  |
 väntvõlli rem.mõõt fordi 351W V8 mootoril
kust võiksin leida väntvõlli originaal ja remontmõõdud fordi 351W mootorile, mootor peaks olema aastast 79.
saalede pealt ei suutnud välja lugeda, kas tegemist originaal või juba remontmõõduga, varuosamüüjad ei oska samuti aidata
igasugune inf teretulnud
tänud ette
henry |
| 21.08.2006 at 21:13 |
|
antennimees
|
väntvõlli rem.mõõt fordi 351W V8 mootoril
Ehk on abiks aasta küll 83 aga võibolla on sama.
ENGINE IDENTIFICATION CODES TABLE
Application VIN Code
5.8L (351") V8 2-Bbl. .................................. G
VALVE SPRING INSTALLED HEIGHT TABLE
Valve Installed Height: In. (mm)
Intake ......................... 1.750-1.813 (44.45-46.05)
Exhaust ........................ 1.578-1.640 (40.08-41.66)
COLLAPSED LIFTER CLEARANCE TABLE
Allowable: In (mm) Desired: In. (mm)
0.098-0.198 (2.49-5.03) .......... 0.096-0.146 (2.44-3.70)
PISTON SIZE CODE CHART
Code Size: In. (mm)
Red ........................ 3.9978-3.9984 (101.54-101.56)
Blue ....................... 3.9990-3.9996 (101.57-101.59)
Yellow ..................... 4.0014-4.0020 (101.63-101.65)
Oversize .003" (.076 mm) ... 4.0002-4.0008 (101.60-101.62)
OIL PUMP SPECIFICATIONS TABLE
Application In. (mm)
Outer Race-to-Housing Clearance .. .0010-.0130 (.025-.330)
Rotor End Play ............................ .004-Max.(.10)
Shaft-to-Housing Clearance ....... .0015-.0030 (.038-.076)
Relief Valve Spring
Tension .......... (1) 18.2-20.2 @ 2.49 (8.3-9.2 @ 63.24)
Relief Valve-to-Bore Clearance ... .0015-.0030 (.038-.076)
(1) - Lbs. @ In. (Kg @ mm).
TORQUE SPECIFICATIONS TABLE
Application Ft. Lbs. (N.m)
Camshaft Sprocket Bolt ..................... 40-45 (54-61)
Camshaft Thrust Plate Bolt .................. 9-12 (12-16)
Connecting Rod Nut ......................... 40-45 (54-61)
Cylinder Front Cover Bolt .................. 12-18 (16-24)
Cylinder Head Bolt ................. (1) 105-112 (142-151)
Damper-to-Crankshaft Bolt ................. 70-90 (95-122)
Exhaust Manifold Retainer Bolt ............. 18-24 (24-32)
Fan-to-Water Pump Hub Bolt ................. 12-18 (16-24)
Flywheel Bolt ............................ 75-85 (102-115)
Fuel Pump
Cylinder Block/Front Cover Bolt ........... 19-27 (26-37)
Intake Manifold Retainer Bolt .......... (2) 23-25 (31-34)
Main Bearing Cap Bolt ................... 95-105 (129-142)
5.8L V8 - VIN [G]Article Text - Tables Only Oil Pump
Mount Bolt ............................... 22-32 (30-43)
Inlet Tube-to-Pump ....................... 10-15 (14-20)
Inlet Tube-to-Bearing Cap ................ 22-32 (30-43)
Pulley-to-Damper Bolt ...................... 35-50 (47-68)
Rocker Arm Fulcrum Bolt .................... 18-25 (24-34)
Water Pump Mount Bolt ...................... 12-18 (16-24)
(1) - Tighten in 3 steps: Step 1 - 85 ft. lbs. (115 N.m);
Step 2 - 95 ft. lbs. (129 N.m); Step 3 -
105-112 ft. lbs. (142-151 N.m).
(2) - After assembly, retighten with engine at operating
temperature.
GENERAL ENGINE SPECIFICATIONS TABLE
Application Specification
Displacement
Cu. In. ............................................ 351
Liters ............................................. 5.8
Fuel System ....................................... 2-Bbl.
HP @ RPM ....................................... 180 @ N/A
Torque Ft. Lbs. @ RPM ................................ N/A
Compr. Ratio ....................................... 8.3:1
Bore ................................... 4.00" (101.60 mm)
Stroke .................................. 3.50" (88.90 mm)
VALVE SPECIFICATIONS TABLE
Application Specification
Intake
Head Diam. ................ 1.770-1.794" (44.96-45.57mm)
Face Angle ......................................... 44
Seat Angle ......................................... 45
Seat Width .................... .060-.080" (1.52-2.03mm)
Stem Diameter ............... .3416-.3423" (8.67-8.69mm)
Stem Clearance .............. .0010-.0027" (.027-.069mm)
Valve Lift ......................... (1) .3776" (9.59mm)
Exhaust
Head Diam. ................ 1.453-1.468" (36.91-37.29mm)
Face Angle ......................................... 44
Seat Angle ......................................... 45
Seat Width .................... .060-.080" (1.52-2.03mm)
Stem Diameter ............... .3411-.3418" (8.66-8.68mm)
Stem Clearance .............. .0015-.0032" (.038-.081mm)
Valve Lift ......................... (2) .3934" (9.99mm)
(1) - 5.8L HO is .4420" (11.23 mm).
(2) - 5.8L HO is .4499" (11.43 mm).
PISTONS, PINS & RINGS SPECIFICATIONS TABLE
Application Specification
Piston Clearance .............. .0018-.0026" (.046-.066mm)
Pins
Piston Fit .............. (1) .0002-.0004" (.005-.010mm)
Rod Fit ...................................... Press Fit
Rings
Ring No. 1 & No. 2
End Gap ....................... .010-.020" (.25-.51mm)
Side Clearance .............. .002-.004" (.051-.102mm)
Ring No. 3
End Gap ...................... .015-.055" (.38-1.40mm)
Side Clearance .................................. Snug
(1) - 5.8L HO piston pin fit is .0003-.0005" (.008-.013 mm).
CRANKSHAFT MAIN & CONNECTING ROD BEARINGS SPECS TABLE
Application Specification
Main Bearings
Journal Diam. ............... 2.9994-3.0002 (76.18-76.21)
Clearance ..................... .0008-.0015" (.02-.04mm)
Thrust Bearing ................................... No. 3
Crankshaft End Play ............. .004-.008" (.10-.20mm)
Connecting Rod Bearings
Journal Diam. ............ 2.3103-2.3111" (58.68-58.70mm)
Clearance ................. (1) .0008-.0015" (.02-.04mm)
Side Play ....................... .010-.020" (.25-.51mm)
(1) - Maximum clearance is .0007-.0025" (.017-.063 mm).
VALVE SPRINGS SPECIFICATIONS TABLE
Application Specification
Intake
Free Length .......................... 2.05" (52.07 mm)
Pressure (1)
Valve Closed ............ 74-82 @ 1.78 (35-38 @ 45.21)
Valve Open ............ 196-214 @ 1.36 (93-97 @ 34.54)
Exhaust
Free Length ........................... 1.87" (47.49 mm)
Pressure (1)
Valve Closed ............ 71-79 @ 1.60 (34-37 @ 40.60)
Valve Open ............ 195-215 @ 1.15 (93-97 @ 29.21)
(1) - Lbs. @ In. (Kg @ mm).
CAMSHAFT SPECIFICATIONS TABLE
Application In. (mm)
Clearance ....................... .001-.003" (.025-.076mm)
Lobe Lift
Intake ............................. (1) .2375" (6.03mm)
Exhaust ............................ (2) .2474" (6.28mm)
Journal Diameter
No. 1 ................... 2.0805-2.0815" (52.84-52.87mm)
No. 2 .................. 2.0655-2.0665" (52.46-52.49mm)
No. 3 ................... 2.0505-2.0515" (52.08-52.11mm)
No. 4 ................... 2.0355-2.0365" (51.70-51.73mm)
No. 5 ................... 2.0205-2.0215" (51.32-51.35mm)
(1) - 5.8L HO is .2780" (7.06 mm).
(2) - 5.8L HO is .2830" (7.19 mm).
____________________________
'05 Chevrolet SSR & '03 Cadillac Escalade EXT |
| 21.08.2006 at 22:17 |
|
stang67
|
väntvõlli rem.mõõt fordi 351W V8 mootoril
leidsin ise ka mingid sarnased numbrid ja nende numbrite järgi tundub, et originaalmõõtudega enam tegemist ei ole, aga kas oskab keegi aidata, kust ma need remontmõõdud võiks välja võluda ? |
| 22.08.2006 at 10:49 |
|
antennimees
|
väntvõlli rem.mõõt fordi 351W V8 mootoril
Remontmõõdud on tavaliselt 0.01" ehk siis 0.25mm sammuga.
____________________________
'05 Chevrolet SSR & '03 Cadillac Escalade EXT |
| 22.08.2006 at 11:06 |
|
stang67
|
väntvõlli rem.mõõt fordi 351W V8 mootoril
mhmm, ei saa enam muhvigi aru
vända pealt mõõdetud tulemused olid 75,93mm ja 58,43, millest võiks järeldada, et tegemist esimese remontmõõduga aga saalede järgi väitsid varuosa müüjad et tegemist originaalsaaledega,mille mõõdud 76,2 ja 58,7 kas selline asi on mõeldav, et vänt on lihvitud aga saaled jäetud originaalmõõtu?
tundub kuidagi kahtlane ? |
| 26.08.2006 at 12:32 |
|
pampkuri
|
väntvõlli rem.mõõt fordi 351W V8 mootoril
quote:
stang67: mhmm, ei saa enam muhvigi aru
vända pealt mõõdetud tulemused olid 75,93mm ja 58,43, millest võiks järeldada, et tegemist esimese remontmõõduga aga saalede järgi väitsid varuosa müüjad et tegemist originaalsaaledega,mille mõõdud 76,2 ja 58,7 kas selline asi on mõeldav, et vänt on lihvitud aga saaled jäetud originaalmõõtu?
tundub kuidagi kahtlane ?
Iga sugu lollusi võib ju teha ma ostsin ka kunagi ühe auto mis oli nii kokku pandud soitis mingi nipiga Rakverest Pärnusse ja siis löppes otsa. Saale taga küljel peaks sul olema siis STS tähis mis tähendab standartit.
____________________________
pamp |
| 27.08.2006 at 10:46 |
|
stang67
|
väntvõlli rem.mõõt fordi 351W V8 mootoril
saalede peal olid sellised andmed:
D.A.B. B
8380 CAP
3-30 DA-49
Raamsaale peal:
D.A.B. 85
8381 CAP
65-39 C
65-39 DA-49
Kas siit loeb midagi välja ? |
| 27.08.2006 at 16:54 |
|
|
