| Poster |
Message |
 ylovoitka
|
 '98 Lincoln Continental PATS süütevõtme programmeerimine
Sooviksin kopeerida Lincoln Conitnental '98 süütevõtit.
Selleks soetaksin kõigepealt võtme tooriku. Näiteks e-bay'st.
Autot valvab PATS (Passive Anti-Theft System), koos kiipvõtmetega.
Kuna olemas on ainult 1 originaalvõti, pole võimalik võtmekoode paljundada auto süütelukupesas ilma spetsiaalse abivahendita (kahe originaalvõtmega saaks lihtsalt programmeerida süütelukus).
Workshop manual väidab, et peab kasutama NGS/SBDS nimelist seadet, mis annab autole loa võõraid võtmeid progeda..
Kas keegi meie kodumaal omab seda sedaet? |
| 01.08.2007 at 10:35 |
|
Vanaisa
  Moderator |
'98 Lincoln Continental PATS süütevõtme programmeerimine
ühe originaalvõtmega peaks ka ju ikka saama:
http://www.cadillac.pri.ee/phpBB//viewtopic.php?t=351 |
| 01.08.2007 at 10:51 |
|
ylovoitka
|
'98 Lincoln Continental PATS süütevõtme programmeerimine
Edastan väljavõtte Factory Service manualist:
Key Programming —Program a Key Using Two Programmed Keys
NOTE: This procedure only works if two or more programmed ignition keys are available and it is desired to program additional key(s). If two keys are not available, follow the procedure in Key Programming—Erase All Key Codes and Program Two Keys .
NOTE: PID SPARE_KY must be enabled for this procedure to operate. If this PID is not enabled, follow the security access procedure above and select Spare Key Programming Switch: Enabled.
NOTE: If the programming procedure is successful, the new key(s) will start the vehicle and the THEFT INDICATOR will illuminate for approximately three seconds.
NOTE: If the programming procedure is not successful, the new key(s) will not start the vehicle and the THEFT INDICATOR will flash. If the programming procedure was not successful, repeat the key programming procedure from Step 1. If the failure repeats, check circuit 1111 (P) (hot at all times) in VIC for proper battery voltage. Repair circuit if voltage is not present. Refer to Diagnosis and Testing to review DTCs and perform pinpoint tests as required.
NOTE: A maximum of eight ignition keys can be programmed to a passive anti-theft system (PATS) equipped vehicle. Use PID NUMKEYS to determine how many keys are programmed to vehicle.
NOTE: If the steps are not performed as outlined, the programming procedure will end.
NOTE: Ignition keys must have correct mechanical key cut for the vehicle and must be a PATS encoded key.
Insert the first programmed ignition key into the ignition lock cylinder and turn the ignition switch from OFF to RUN (maintain the ignition switch in RUN for one second).
Turn the ignition switch to OFF and remove the first key from the ignition lock cylinder.
Within five seconds of turning the ignition switch to OFF, insert the second programmed ignition key into the ignition lock cylinder and turn the ignition switch from OFF to RUN (maintain the ignition switch in RUN for one second).
Turn the ignition switch to OFF and remove the second key from the ignition lock cylinder.
Within ten seconds of turning the ignition lock cylinder to OFF, insert the unprogrammed ignition key (new key) into the ignition lock cylinder and turn the ignition switch from OFF to RUN (maintain the ignition switch in RUN for one second).
If it is desired to program additional key(s), repeat the key programming procedure from the beginning.
|
| 01.08.2007 at 13:32 |
|
Vanaisa
Moderator |
'98 Lincoln Continental PATS süütevõtme programmeerimine
Õigus - ei lugenud ise enda antud linki korralikult läbi - vanadus, mis muud  |
| 01.08.2007 at 18:00 |
|
|
